PRODUCT BROCHURES
Visit the product section of this website to learn more about our full line of IDEAL products for your jobsite.
TEST & MEASUREMENT
SureTrace Circuit Tracer Brochure
DATACOMM/NETWORKS
Compression Solutions Guide
TOOLS & SUPPLIES
Professional Electrician Pliers Brochure
Twist-a-Nut™ Screwdriver Line Brochure
Conduit Bender Guide
FISHING, BENDING & LUBRICANTS
E-Class™ Fish Tape Instructions
PRODUCT VIDEOS
Watch now to see some of our tools in action
TEST AND MEASUREMENT
SureTrace™ Circuit Tester
How to Choose a Tester
Tester and Meter Safety Categories
DATACOMM/NETWORKS
FT-45™ Crimping Tool & Modular Plugs
RTQ™ XR™ F Compression Connector
ELECTRICIAN HAND TOOLS GUIDE
Learn more about our top hand tools for electrical professionals
SCREWDRIVERS
Cabinet Tip Screwdriver
- Slotted tip is the same dimension as the shaft
- Used for outlet face-plate screws (3/16") to attach cover without scratching cover surface
Keystone Tip Screwdriver
- Slotted tip, keystone shaped for additional strength
- Used when additional strength is required
Phillips Tip Screwdriver
- Cross tip, comes in many sizes to match screw head
- Used for Phillips screw heads
- Most common size used by electricians is P#2 for screws on outlets, switches, and similar devices
Square Recess Screwdriver
- Square tip, comes in many sizes to match screw head
- Used for Square Recess or Robertson screw heads
- Most common size used by electricians is SQ#2 for screws on outlets, switches, and similar devices
Combo-Tip Screwdriver
- Combines the tip attributes of either Slotted and Square or Slotted, Phillips, and Square
- Combo-Tips are used on Combination Head screw heads
- The Combo-Tips provides better grip on these type of screws due to its many surfaces contacting the screw recesses
PLIERS
Linesman Pliers
- Also referred to as "Side-Cutters" and "Hammers"
- Used for cutting, pulling, and stripping wire
- Crimp dies (U or Flat) used to compress crimps around wires
- Fish tape pullers aid in pulling wires and tapes
Diagonal Cutting Pliers
- Also referred to as "diagonal cutters"
- Cuts wires, pulls, and rocks tapes
- Available in both flat (standard) or angled-head (better for flush-cuts and rocking out staples)
Long-Nose Pliers
- Also referred to as "needle nose" or "long reach" pliers
- Good for reaching inside electrical boxes, twisting loops on wire, cutting wire, and grabbing/twisting electrical box pry-outs
Tongue & Groove Pliers
- Also referred to as "pump pliers" and "arc joints"
- Used for tightening conduit fittings, lock-nuts, and similar threaded things
Slip-Joint Pliers
- Also referred to as "combination" or "standard" pliers
- General purpose plier for utility use
- Slip joint pivot facilitates expanding the jaw capacity to grip larger nuts and bolts
WIRE STRIPPERS
Wire Strippers
- Used to strip electrical insulation from wires
- Wire looping hole can be used to prepare wires
OTHER COMMON HAND TOOLS
Multi-Crimp Tool
- Cutter nose (knife and anvil) used to cut wires
- Crimping dies for insulated and non-insulated barrel crimps and crush crimps
Cable Cutter 2/0
- Also referred to as "parrot jaws"
- Cuts large gauge wire, up to 2/0 AWG Cu or AI cable
- Used primarily by commercial electricians on feeder cable
- Not for use on steel wire, bolts, or staples
Adjustable Wrench
- Used to tighten or loosen nuts and bolts
- Adjustable head allows it to be used with different sizes of fastener heads
INDUSTRY RESOURCES
Join the tightknit community where you can lead and advance your career. Below is information on some of the organizations that you can join as a budding professional.
Associated Builders and Contractors
Electrical Training Alliance
Independent Electrical Contractors
International Brotherhood of Electrical Workers
National Association of Homebuilders
National Center for Construction Education and Research
National Electrical Contractors Association
